The data and AI platform for engineering teams
Turn engineering files into clean, versioned datasets. Then ask questions and build apps with AI.
Projects
- Wing flutter analysis
- Supplier quality
- Fleet telemetry
Workspace
- Files
- Datasets
- Chat
Wing flutter analysis / Datasets
Accelerometer runs
v3 publishedv4 draft · 2 changes| run_id | mach | altft | peak_loadg | trace | limit 2.5 g | |
|---|---|---|---|---|---|---|
| R-103 | 0.78 | 15,000 | 2.97 | Exceeds | ||
| R-106new | 0.84 | 20,000 | 2.41 | Near | ||
| R-104 | 0.82 | 15,000 | 2.18 | Within | ||
| R-102 | 0.70 | 10,000 | 2.11 | Within | ||
| R-101 | 0.62 | 10,000 | 1.84 | Within |
Releases
- v4Draft: adds run R-106, renames acc_z to peak_loadAna, now
- v3Adds 2 files from the October campaignBob, Oct 16
- v2Sets units for 6 columnsAna, Oct 9
Chat
Accelerometer runs · v3Which runs exceed the 2.5 g limit? Plot peak load by run.
Thinking…
The limit applies to peak_load in g. I'll read release v3, take each run's maximum, and mark 2.5 g on the plot.
● Query accelerometer-runs@v3
⎿ 1,248 rows · 8 columns
● Python
df = load("accelerometer-runs@v3")peak = df.groupby("run_id").peak_load.max()ax = peak.plot.bar()ax.axhline(2.5, ls="--")
⎿ Figure 1
Only R-103 exceeds the limit, at 2.97 g and Mach 0.78. R-106 is close, at 2.41 g.
Ask a follow-up…
Flange sizer
v1Built from chatData: Material allowables v5Pipe OD
50.8 mmPressure
300 psiBolts
6Material
- Yield (Fty)
- 880 MPa
- Density
- 4.43 g/cm³
- From Material allowables v5
Bolt load
1.22 kN
Bolt margin
+3.88
Thickness
4.9 mm
Mass
84 g
#8 bolts on a 67.1 mm circle · flange OD 77.1 mm
Waiting for a request
Chat
Material allowables · v5Build an app that sizes a bolted flange for a 2 in titanium bleed-air duct. Use our Material allowables dataset, and show the part in 3D.
Thinking…
Material properties should come from the team's Material allowables v5 release, not from numbers typed into code. The app reads yield and density from it, checks the bolt load, and draws the flange.
● Query material-allowables@v5
| alloy | fty MPa | ρ g/cm³ |
|---|---|---|
| Ti-6Al-4V | 880 | 4.43 |
| Inconel 625 | 414 | 8.44 |
| Al 6061-T6 | 276 | 2.70 |
⎿ 3 alloys · 12 columns
● Create app flange-sizer
alloy = dataset("material-allowables@v5").row(material)load = 1.5 * p * area(gasket) / boltsmargin = BOLT_MAX / stress(load) - 1t = thickness(p, alloy.fty)return <Flange3D od bolts t />
⎿ App ready · v1
Your Flange sizer reads Ti-6Al-4V from Material allowables v5. At 300 psi with 6 bolts, each bolt carries 1.22 kN and the margin is +3.88.
Ask a follow-up…